Home > Fax Error > Fax Error Codes Ricoh

Fax Error Codes Ricoh

Contents

Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##734 [ RX ] Excessive NACK transmission (3 times) due to failure This error is very rare because normally a remote machine does not answer if it cannot receive a document. Cause: Defective internal unit. Load valid size paper in the tray, and configure the paper size settings under [System Settings] accordingly. Source

You may need to insert a pause between dial digits. Solution: Have the other party lower the transmission start speed to 4800 bps. Status Codes Value Description Comments -11 Pre-processing The system has received your message and is preparing a fax. Solution: Replace the button control unit (operation unit, etc.). ##232 [ TX ] ENCODE control unit malfunction. http://support.hp.com/us-en/document/buu02549

Fax Error Codes Ricoh

The remote user canceled the fax transmission by pressing the Stop key immediately prior to, or just as the local machine answered the call. A. Have the telephone company check the line. 431 The sending fax machine did not receive a response after terminating a transmission. C.

Solution: Replace the DECODE control unit (PRINT, etc.). ##238 [ RX ] PRINT control unit malfunction. Cause: Printer control DRAM malfunction Solution: Power cycle the machine. No action required. 311 The user of the local machine pressed the Stop key, causing the session to be prematurely terminated before all pages have been sent. Error Code 700 Error In Fax Transmission Cause: CPU malfunctioned due to noise.

Depending on your printer, a fax error code might display on the printer control panel or on a fax history report. Canon Fax Error Codes If not, reconfigure the local machine for a normal fax transmission. Solution: Retransmit at a later time. ##285 [ TX ] DCN reception after EOP transmission. http://support.ricoh.com/bb_v1oi/pub_e/oi_view/0001042/0001042778/view/op_guide/unv/0313.htm Solution: Replace NCU PWB ##263 [ TX / RX ] Fail to respond for 20 seconds after detecting preamble.

A. Fax Error 346 Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##716 [ TX ] Fail to fall back during ARQ transmission. B. Solution: Resend Solution: Record the protocol on DAT tape and then request the Canon Technical center to analyze the information. ##205 [ TX ] Data error during image memory

Canon Fax Error Codes

Solution: Add an EPT on the V29 modem signals. http://www.worldoffax.com/G3%20Service%20Codes.htm Cause: Defective internal unit; (RECORD will not go on during memory copy). Fax Error Codes Ricoh Cause: Defective internal unit. How To Disable Ecm On Hp Fax Machine D.

Cause: The other party cannot receive RR properly due to poor line conditions. this contact form Recorded answer This usually occurs if the destination number is answered by an automated attendant. Ask the remote machine user to reset the remote machine. Note that this confirmation is provided by the receiving fax machine, indicating it confirms that it has received all pages successfully. 1 Internal error Call disconnected after several minutes without getting Hp Fax Error 344

Cause: Power unit trouble Solution: Replace power unit ##330 [ TX / RX ] Power supply unit ACVIN signal abnormality. A. In some cases this error can occur if the other fax machine is using a fax format incompatible with the HP fax. 422 423 A handshaking (connection) error occurred at some have a peek here A.

Cause: The operation of the UPI to control the DECODE operations did not finish properly. Hp Fax Comm Error Solution: Power cycle the machine (unplug unit). B.

See Administrator Settings. 1XXX32 to 1XXX84 An error occurred while sending a fax.

Cause: BJ cartridge installation surface is defective. A. If you cannot make calls this way, contact your telephone company. Ecm Setting On Fax Solution: Replace NCU board. ##264 [ RX ] Fail to receive picture signals within 10 seconds after entering picture reception status.

The receiving line might be out of order or disconnected. 3933 Busy Unassigned number or telephony error. 3935 No answer (might be out of paper) 3936 Human voice answer Cause: Other party cannot properly receive phase signal due to poor line conditions. Confirm that the local user really wants to attempt a poll reception. Check This Out If the local machine consistently gives this error code from different fax numbers, then the issue is probably hardware related and the machine should be replaced or serviced.

Under rare conditions, incompatibility between the two machines might cause the remote machine to abandon the call. A. An error code can have more than one definition (cause), and more than one solution. Solution: Transmit to a FAX whose bits 33 and over are not covered by recommendations.

Image density is too high. Errors might still occur, and might result in a degraded image quality on the received page. Solution: Have the other party boost their transmission level so they can receive picture signals or EOM properly.