Home > Fax Error > Canon Fax Error Code Ng

Canon Fax Error Code Ng

Contents

It is either '1' or '0', modulated according to frequency, and is used as G3 procedure signals. passwords. • If the other party is a non-Canon machine, see the password to either 11111111' or '255'. • Record the protocol on a DAT or MD, and have it analyzed Cause 2 The receiving machine is not a G3 fax. Solution: Perform echo counter-measures as listed in Service manual. Source

Page 203 Chapter 2: Service Error Codes ##1026 [ TX/RX ] Non-selected user clearing Cause Remedy • Cause number #26 (Non-selected user • Start a communication once again. Page 98 Chapter 2: Service Error Codes ##244 [ TX/RX ] The unit used to control OPT2 malfunctioned Cause Remedy • The operation of the IC used to control • Replace A. Solution: Have the other party boost the transmission level to receive EOM or PIS properly. ##506 [ RX ] Fail phase synchronization during G1 reception.

Canon Fax Error Code Ng

Repair Send your Canon product for repair. Cause: The other party released the line during transmission. Page 83 Chapter 2: Service Error Codes ##122 [ TX ] ITU-T-compliant (DIS bits 33 through 37) transmission function is absent Cause Remedy • Bit 33 of DIS received from the Provide echo remedy 1 Using a manual call, press the Start button after hearing the 1st DIS from the other party.

A. Page 108 [ TX ] After transmitting EOP, a signal other than PIN, PIP, MCF, RTP, or RTN was received Cause Remedy • The procedure signal has a fault. • Record Increase the T5 timer setting to avoid an error. Canon Fax Error Code 104 Solution: Have the other party boost their transmission level so they can receive picture signals or EOM properly.

munication. ##286 [ TX ] DCN has been received after transmitting Cause Remedy •... However, the ability to send the entire document improves. B. https://support.usa.canon.com/kb/index?page=content&id=ART141048 Page 94 Chapter 2: Service Error Codes ##232 [ TX ] The unit used to control the encoder is faulty Cause Remedy • The operation of the IC used to control

tiated without starting MF1 mode. [Japa- nese model] 1-4 Chapter! : User Error Codes #006 [ TX ] Transmission cannot be made [ RX ] Phase synchronization fails in OLD-FM Cause Canon Result Ng Cause: SCNT PWB malfunction. crease the transmission level so that CFR2 may be received correctly. View All Products Printers & Faxes High quality printers and faxes for your business.

Canon Fax Machine Error Codes

Page 65 Chapter 2: Service Error Codes ##009 [ TX/RX ] The end of the tonal signal from the other party cannot be detected Cause Remedy • The line suffered large Page 77 Cause Remedy • The procedure signal is faulty. • Record the protocol on a DAT or MD, and have it analyzed by the local Canon office and/or Technical Center. Canon Fax Error Code Ng Page 177 [ TX ] In ECM transmission, a signal other than ERR was received after transmission of EOR-NULL Cause Remedy • The procedure signal is faulty. • Record the protocol Canon Error #099 Increase the DTMF transmission level so that the sever may receive the DTMF signal correctly.

Solution: Replace the board containing the BJ controller. this contact form Note: if the capacity of the absorption pad is unclear, register a value corresponding to the quantity of absorbed ink in pad Solution: Replace the PCNT PWB, and register a Page 115 Chapter 2: Service Error Codes ##304 [ RX ] Memory copying cannot be used Cause Remedy • An internal unit is faulty (i.e., during • Correct it by referring Ask the remote machine user to reset the remote machine. Canon Fax Error #099

Cause: The user telephone number is not registered (if the receiver is a Ricoh 3000L) Solution: Register user telephone number. Remedy Wait until the Address Book Import/Export function from the Remote UI or the other sending component is complete, and then try sending again. #711 Cause 1 The Mail Box and Cause: The other party cannot receive NACK signals properly due to poor line conditions. have a peek here Page 201 Chapter 2: Service Error Codes ##1019 [ TX/RX ] No answer from user (user alerted) Cause Remedy • Cause number #19 (No answer from user • Wait a while,

Cause: (Q signal transmission after picture signals); The other party cannot receive picture or Q signals properly due to poor line conditions. G3 Fax Solution: Replace the backup secondary battery. OPT2 did not end normally. ##260 [ TX/RX ] System error occurred between modem and system control board...

A.

Cause 2 An original was not scanned properly, or the orientation of the original was incorrect. Page 27 Chapter1: User Error Codes #025 [ TX/RX ] Auto-dial setting is wrong Cause Remedy • The settings require registration of a • If auto-dialing is of a type requiring Cause: Defective DES sensor. Reserved Communication Jobs Were Cleared. Introduction 6.

Remedy Check to see that the power plug is firmly inserted into the power outlet and that it is not in a situation where the power can easily be turned OFF. Solution: Print the entire data, clear the memory and then re-register the data. Remedy Try sending again. #829 Cause 1 Data that contains more than 1,000 pages is received. Check This Out have it analyzed by the local Canon office and/or Technical Center. • When DIS was received during CEP2 •...

Page 79 MCF, RTP, RTN, PIP, or PIN was received Cause Remedy • The procedure signal is faulty. • Record the protocol on a DAT or MD, and have it analyzed